Trinity motor lathe w/almost new 55t drive motor $75
(http://i82.photobucket.com/albums/j249/limey420/lathe1.jpg)
(http://i82.photobucket.com/albums/j249/limey420/lathe3.jpg)
Intergy setup station and pit board made by our own gotnitro so you know its awesome. Hudy1/10th setup decal (lifting a little bit but all good) $65
(http://i82.photobucket.com/albums/j249/limey420/setup.jpg)
Pixie 20amp esc $25.
(http://i82.photobucket.com/albums/j249/limey420/pixie20.jpg)
Rc18 mt set up as a "B"
Mamba 8000kv brushless with heat sink on motor
3 cell lipo pack....
Ti-turn buckles
Alu shock bodys
Carbonfiber Batt hold down
HS 65mg servo, upgraded servo, stock is still good and included.
Alu servo hold down, steering rack, c-hubs, knuckles and carriers.
Touring car wheel adapters
Proline dirthogs on yellow dish
Foam nitro tires from a serpent for the road...
MIP CVD's
MIP rear diff
Tons of extra parts in case...
NIB parts:
3x ballstud kit
1x outdrive set
3x diff rebuilt kits
2x diff gears
1x steel turnbuckles
This thing is very fast and flips over backwards on demand as long as there is traction. The lipo battery is a huge power upgrade for the mamba and gives you all the power you want...by the time you get to full throttle it's too far away....60mph+
Over $600 invested
$200
(http://i82.photobucket.com/albums/j249/limey420/rc18t8.jpg)
(http://i82.photobucket.com/albums/j249/limey420/rc18t6.jpg)
(http://i82.photobucket.com/albums/j249/limey420/rc18t5.jpg)
(http://i82.photobucket.com/albums/j249/limey420/rc18t2.jpg)
Muchmore motor master dyno with optional billet motor stand $150
(http://i82.photobucket.com/albums/j249/limey420/dyno.jpg)
Used stock motors....all for $20
(http://i82.photobucket.com/albums/j249/limey420/motors.jpg)
Hobbico Quick Field Charger MKII:
2x 8 cell GP1100 nimh
1x 3cell lipo, 11.1v, 1400mah 18c
2x 7cell 1000mah nimh generic cells
2x deans adapters
Great charger, charges two packs at once.. does nimh, nicd, lipo's
Low useage on lipo and GP packs, always proberly maintained....1000mah packs are in fair condition.
$80
(http://i82.photobucket.com/albums/j249/limey420/charger2.jpg)
(http://i82.photobucket.com/albums/j249/limey420/charger3.jpg)
Hitec Lazer 4:
4 Channel with V-mixing
2x RX.....1x micro ss...1x feather
3x HS 55 servos
Batt and charger
$85
(http://i82.photobucket.com/albums/j249/limey420/hitec2.jpg)
(http://i82.photobucket.com/albums/j249/limey420/hitec3.jpg)
hi dave very intrested in your mini would you take $175 ifso could i get it sunday thanks cody 8O
ment to pm that :lol:
no thanks worth every penny at $200
RC 18 pending.....
hitec radio also in the works for more than asking 8)
how much extra for the radio
extra radio?
nvm
hitec radio gone
offers?
setup station, rc18, charger gone......
update:
Lathe $60!!!
pixie$20
Dyno $125!!!!
PM about dyno.
Dyno gone....................
il take the pixie
noone wants a $50 lathe?